As part of the commissioning, the calibration of the temperature sensors, as well as the measurements of the quadrupole mover travel distance has been done in the tunnel. Finally, the cabling has been done and basic tests were performed. Then all mentioned components have been aligned according to the specifications. They have been mounted according to the designed positions. During installation step, the following main components were rolled into the tunnel: - undulators with the control cabinets, intersection control cabinets, phase shifters, quadrupole movers, correction coils. In general, the work can be divided into 3 different steps: installation, alignment, and commissioning. This article describes in detail the steps of hardware installation and commissioning of components for undulator systems at European XFEL. M. Yakopov, S. Abeghyan, S. Karabekyan, J. Pflüger.Installation and the Hardware Commissioning of the European XFEL Undulator Systems This early injector commissioning (EIC) is embraced as an opportunity to gain valuable experience with the majority of the LCLS-II controls, especially the 1MHz high performance subsystems (HPS), prior to first light. An added challenge was a decision to commission the injector ~1.5 years ahead of the rest of the machine, in FY 2018. Collaboration between the LBNL APEX controls community and SLAC LCSL-II controls team proved vital in advancing the controls architecture toward standardized implementations integrated with the rest of LCLS-II. In 2015, responsibility for controls design and fabrication was transferred to SLAC from LBNL to promote commonality with the rest of the LCLS-II control subsystems. The LCLS-II Injector section that comprises low energy from the gun up to the location of the first cryomodule is based on the LBNL Advanced Photo-Injector Experiment (APEX), and is being provided by LBNL. Construction is underway with first light planned for 2020. LCLS-II is a superconducting upgrade to the existing Linear Coherent Light Source at SLAC with a continuous wave beam rate of up to 1 MHz. SLAC LCLS-II Injector Source Controls and Early Injector Commissioning Status of the European Spallation Source, T. This paper will present our proposition of architecture for the SARAF Linac using the new CEA Irfu hardware and software platforms. Currently, CEA Irfu is in charge of the design, construction and commissioning at SNRC of the project SARAF-LINAC (MEBT and Super Conducting Linac) including its control. ![]() We have made our CEA Irfu control platform evolve by retaining relevant and evolutive ESS solutions. Our 3-year collaboration with ESS has given us the opportunity to use new COTS hardware. Our Institute CEA Saclay Irfu was in charge of the EPICS based control system platform for the accelerator projects Spiral2 at Ganil in Normandy and IFMIF/LIPAc at JAEA/Rokkasho (Japan). Eject, Load, and play your game.ICALEPCS2017 - Table of Session: THPHA (Poster Session) THPHA - Poster Session (12-Oct-17 16:45-19:00)ĬEA Irfu EPICS Environment for the SARAF-LINAC Project Step 4: Use the configs listed, make an image in Alcohol 52% then mount it in Daemon. Step 4: Install the latest SCSI Pass Through (1.55 I believe) Install Daemon Tools 4.06, and put Yasu in the root folder.Īll Checked, Uncloak then cloak, starts on startupĭrives -> Make sure to eject when the image is mounted in Daemon Tools and cloaked in Yasu, then load as the final step before playing the game. ![]() Step 3: Download Daemon Tools 4.06 and the latest Yasu Release. Securom, Normal DPM, 1x DPM, Slowest Speeds, Percision = Normal Step 2: Make the image, with these settings: Step 1: Download Alcohol 52%, install without toolbar (you have a choice, the website lies) Asus motherboard p5ld2 p4 3.8ghz, 3gb ram. ![]() But i know the image works because i tried it on my other pc. I've tried uninstalling the games several times tried different versions of daemon tools and also a different image. If I run command and conquer 3 or Company of heroes opposing fronts, both games detect emulation Iam using the latest daemon tools lite V4.11.2 and Iam also using yasu v1.4.780. Hello can someone please helpme with this problem that iam having with my pc.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |